Using Store as ADMIN

Hampton Tall Single Gate

  • Hampton Tall Single Gate
  • Brand: BIC
  • Product Code: BIC710
  • SKU:
  • Availability: In Stock
    Delivery: Direct from the factory in 2 to 4 weeks
  • £264.95


Free Delivery*

Share



The Hampton Tall Single Gate is a beautifully crafted gate that combines wood and metal to create a strong yet elegant gate that would complement even the most stately homes. The gate is handmade in the UK and features an open top section that is filled with vertical metal rods, with attractive spear finials running across the top of the gate. The main body of the gate is solid tongue and groove, framed on both sides and across the top. The timber is smooth planed Scandinavian Redwood which has been pressure treated for a long, maintenance free life. The gate has two vertical, four horizontal and two diagonal heavy duty braces on the back for maximum strength and durability. The overall height of the gate is 1800mm (71”).

It is recommended that wooden gate posts are used when installing these gates. Optional smooth sawn pressure treated 10cm square posts are available.

An optional galvanised fittings pack that includes a Ring Latch and 2 x 18 inch Hook and Band Hinges is also available.

The Hampton Tall Single Gate is available in the following sizes:

OPTIONGATE WIDTHGATE HEIGHTPRICE
75cm750mm (29.5")1800mm (71")£264.95
90cm900mm (35.5")1800mm (71")
£299.95
105cm1050mm (41.5")1800mm (71")
£334.95

See size chart below to calculate how much space you will require to install your gate when using our 10cm square gate posts.

GATE WIDTHEXPANSION GAPPAIR OF POSTSTOTAL GAP REQUIRED
75cm1cm20cm96cm (38")
90cm1cm20cm111cm (44")
105cm1cm20cm126cm (50")

If our standard sizes won't fit, a made to measure service is available for this gate. Please click the tab below to be directed to the made to measure page.

View Made to Measure

Information about your gate

Fittings. The Hampton gates are not supplied with any fittings; however an optional fittings pack is available which includes the correct size hinges and latch for this weight of gate. The fittings we have available are galvanised to prevent rust. The gate has three horizontal braces on the back. Hinges should be fitted to the top and bottom brace.

Wooden Posts. Posts should be dug in approximately 60cm deep and held in place with concrete, or bolted to the wall using masonry bolts or frame fixing screws. A small gap must be left between the post and the gate to allow for expansion of the wood.

Finish. The Hampton gates are supplied pressure treated which leaves the wood with a temporary green tint. If left to weather, the wood will fade to a silvery grey colour; however you can change the colour straight away by staining the wood using Protek Timber Eco Shield, or it can be painted after it has been allowed to weather for at least 3 months using a product compatible for use with pressure treated timber. The metalwork is supplied black powder coated when required this can be topped up with a suitable exterior metal paint such as Hammerite.

Specification

SIDE FRAME70mm x 70mm
BACK BRACING70mm x 54mm and 44mm x 44mm
TONGUE & GROOVE BOARDS95mm x 14mm
METAL BARS16mm diameter solid steel
JOINTSMortise & tenon
WOOD TREATMENTPressure treated
METAL TREATMENTBlack powder coated

 Direct from the factory in 2 to 4 weeks
 Delivery to UK mainland only. Surcharges apply to Highlands.

 FREE
 Surcharge applies for Highlands and Islands
 Not available for delivery

Write a review

Note: HTML is not translated!
    Bad           Good
The product is currently Out-of-Stock. Enter your email address below and we will notify you as soon as the product is available.







Add GardenOasis App. Press Then select "Add to Home Screen"